KitchenAid · Silicone Baking Molds
Ama Pear Silicone bowl liner for KitchenAid 5QT mixer single piece baking accessory
Silicone bowl liner, but coating details absent. Limited PFAS risk data.
Silicone is inherently low-risk, but KitchenAid does not disclose surface treatments or coatings. Third-party testing data is unavailable for this specific product.
Still want this one anyway? Check the price on Amazon. We’d swap it.
Material
silicone, coating/treatment unspecified
Brand disclosure
Brand is silent on PFAS
Lab data
No public lab test
Why this grade
Non-stick, chemistry undisclosed
Marketed non-stick without stating the coating chemistry.
Category baseline
cookware is a category where PFAS exposure is more common.
No PFAS disclosure
No public statement about PFAS in this product.
The full breakdown
What it's made of and why it matters
This is a food-grade silicone liner designed to sit inside KitchenAid's 5-quart mixing bowl. Silicone itself is a polymer chain of silicon and oxygen with organic groups attached, and does not contain the lead, cadmium, or ceramic glazes that pose leaching risks in traditional cookware. The critical unknown here is whether any coating, anti-stick treatment, or reinforcement additive was applied to the silicone during manufacture. KitchenAid has not publicly disclosed the full formulation or whether any flame retardants or processing aids remain in the final product.
The brand's record and disclosure
KitchenAid (owned by Whirlpool) does not maintain a public material safety transparency statement for silicone accessories. The company has no known recalls specific to silicone bowl liners for chemical hazards. Certifications for this product (FDA food-contact status, EU compliance, or third-party testing) are not stated in publicly available product literature. This silence is typical for small silicone kitchen accessories and does not automatically indicate a problem, but it means independent verification of chemical safety claims is limited.
How it compares in its category
Silicone bowl liners are a lower-risk alternative to older rubber or plastic bowl covers, which may off-gas phthalates or other volatiles. Most major mixer manufacturers (Cuisinart, Electrolux) offer similar silicone accessories with comparable disclosure levels. Glass or stainless steel bowl replacements eliminate leaching risk entirely but cost more and are heavier. Silicone liners sit in the middle of the risk-convenience spectrum for this use case.
If you buy it
Wash the liner thoroughly with warm soapy water before first use to remove any manufacturing residue or dust. Do not expose it to direct flame or temperatures above 400 degrees Fahrenheit; normal KitchenAid mixing stays well below this. Inspect it annually for tears, discoloration, or odor changes, which may signal degradation. Replace it if it becomes tacky, discolored, or develops cracks that might allow food contact with the bowl underneath.
Beyond PFAS: other things we checked
Established hazard classes for this product type, assessed from public information. These never change the PFAS grade; a Likely flag caps the Verdict at “Buy with care.”
Silicone leaching (oligomers/processing aids)
Some food-grade silicones can release small quantities of oligomeric siloxanes into acidic or fatty foods at elevated temperatures. No recalls or reports specific to this KitchenAid product exist. Risk is reduced at typical mixing bowl temperatures (below 150 degrees Fahrenheit during use).
Coating degradation and fragmentation
If the silicone was treated with a separate non-stick or reinforcement coating (not confirmed for this model), flaking over years of use could introduce particles into food. No evidence of this in public records for this specific product.
Formaldehyde resins (binders or colorants)
Food-grade silicones typically do not require formaldehyde-based binders, but dyes or reinforcing agents could theoretically contain them. KitchenAid has not disclosed the source or composition of any colorants in this liner.
Aluminum migration (if used with aluminum bowl)
The silicone liner sits between food and the metal bowl, creating a barrier that prevents direct aluminum contact. This eliminates the primary route of aluminum leaching from mixer bowls.
Bacterial or mold growth on unsealed seams
Single-piece design reduces seam trap points, but any gap between liner and bowl rim could harbor moisture and bacteria if not dried thoroughly. Proper air-drying after washing mitigates this practical risk.
What we don’t know
This grade is a model-based estimate from public materials, coatings, and brand disclosure at 45% confidence. It is not a lab result.
No independent PFAS lab test is on record for this exact product. A lab test could move the score in either direction.
The brand has not made a specific, verifiable PFAS-free statement, so part of this score reflects that missing disclosure rather than a confirmed material.
Formulations and coatings change between production runs. Always check the current label before buying.
Safer alternatives in Silicone Baking Molds
Fat Daddio's
ProSeries Silicone Baking Mat
silicone (elastomer)
Silicone mat carries lower PFAS concern; no nonstick coating needed.
⚠Risky category by default
Fat Daddio's
Silicone Baking Mold
silicone elastomer
Lower concern. Silicone baking molds rarely contain PFAS.
⚠Risky category by default
Fat Daddio's
Silicone Hemisphere
silicone
Lower concern. Silicone baking molds typically PFAS-free.
⚠Risky category by default
More silicone baking molds grades
How we score: every product runs through the same public 0–100 rubric based on materials, coatings, brand disclosure, lab findings, and recalls. See the full methodology → Spotted a mistake? Report an error.